DIGITAL CIRCUIT LABORATORY
Features :
- Seven circuit boards form 19 experiments.
- Suitable for combinational logic, sequential logic, and microprocessor circuit experimentation and design.
- Ideal tool for learning the basics of digital logic circuits.
- Step-by-step exercises and application.
- Integrated training system, with complete <INSTRUCTION>.
- Combination with M21-7000 digital-analog training system as main unit.
- Step-by-step exercises and application .
- Expandability and flexibility of experiments greatly increased by large breadboard.
- Board can be changed easily.
The MZM-3013 digital circuit laboratory is a comprehensive and self-contained system suitable for tuition and experimentation with a range of digital electronics circuits. All necessary equipments for digital logic experiments such as power supply, signal generator, switches and displays are built-in on the main unit. The 7 circuit boards cover a wide variety of essential topics in the field of digital logic. It is a time and cost saving device for both students experiment and researchers interested in developing and testing circuit prototypes.
THE FULL LIST OF EXPERIMENTS PERFORMED USING DTS-1 ~ DTS-7
DTS1
DTS2
DTS3
DTS4
DTS5
DTS6
DTS7
|
Experiment 1 |
Transistor Switching Characteristics |
|
SOLDERLESS BREADBOARD |
Interconnected with 2820 tie points nickel plated contact,fitted all DIP sizes and all components with lead and solid wire AWG # 22-30 (0.3-0.8mm).It can be changed and replaced for different purpose and can be connected with demonstration panel. Therefore, it is very convenient for both teachers and students. |
|
DC POWER SUPPLY |
|
|
A. Fixed DC output |
+5V, 1A |
|
B. Fixed DC output |
-5V, 1A |
|
C. Variable DC output |
0V to +15V, 1A |
|
D. Variable DC output |
0V to –15V, 1A |
|
POTENTION METERS |
|
|
A. Variable resistor VR1 |
1kΩ |
|
B. Variable resistor VR2 |
100kΩ |
|
FUNCTION GENERATOR |
|
|
Frequency range |
1Hz－10Hz |
|
Amplitude |
Sine wave output：0－10 Vpp variable |
|
TWO DIGITS OF 7 SEGMENT LED DISPLAY |
|
|
TWO PULSE SWITCH |
2 pcs pushbuttons contain switches debouncer for eliminating the bounce caused by switch from“open” to“close” or from“close” to“open”position. |
|
SIXTEEN DATA SWITCHES |
16pcs toggle switches and corresponding output point. When switch is set at “down”position,the output is LO level; contrarily, it is to be HI level while setting at “up”position. |
|
SPEAKER |
2-1/2 inch diameter, 8 ohm/0.5W to be used for load. |
|
FOUR CHANNEL ADAPTOR |
Both of the two banana sockets' and two BNC jacks' point tips are changeable. It is suitable for M21-7000 to be connected with peripherals. |
|
SIXTEEN BITS LED DISPLAY |
16 red LED's separate input terminals. The LED will be lighted up when input is at “HI level” ,and it will be turned off when it is at no input or at “LO level”. |
|
UNIVERSAL CONNECTOR FIXED HOLDER |
|
|
It reserves universal connector fixed holder on the panel in order to be connected with various universal connectors, |
(1) Straight header 60 pin |
|
(2) Card edge connector 2.54mm 62pin |
|
|
(3) D sub25 pin connector, male & female |
|
|
(4) Card edge connector 3.96mm 56pin |
|
1. Accessories
- Power cord
- Pin leads: 10cm 20pcs, 20cm 20pcs
- User manual+ instruction of analog circuit experimentations
2. INPUT VOLTAGE: 110~127VAC±10% 60Hz, 220~240VAC±10% 50Hz Switchable
3. DIMENSIONS:
- Main unit (W×H×D): 258×95×334mm
- Circuit board: 165×170mm
4. WEIGHT:
- Main unit: 4.5kg
- Circuit board: 0.4kg×7